Cold Laser Equipment - 877-LASER-50 or 877-527-3750 (Anytime)
We sell cold lasers only to Licensed Health Care Professionals
Cold Laser components sold by Laser-Therapy.US, 56 Woodland Drive, West Paterson, NJ 07424
Manufactured by and for: Healing Lasers Design Company, Cape Girardeau, MO a US FDA Registered Facility
60 DAY RISK FREE TRIAL* AND A ONE YEAR WARRANTY INCLUDED
FREE SHIPPING (USA only) with purchase of qualifying new cold laser (till Thursday 03/11/10)
cold laser suggested set up instructions
Our economical cold lasers allow you to offer affordable low level laser therapy to your patients increasing patient satisfaction, increasing referrals and your income.
Many of our clients report great success using 9 Hz +/- and 16 Hz +/- as treatment frequencies with treatments starting with the 808nm 150mw wand for about one or two minutes per treatment area and then using the 635nm 5mw wand for about four minutes per treatment area. One theory is the deeper penetrating 808nm wand and the less penetrating 635nm wand treat surrounding tissue that may also be irritated or inflamed.
Suggested set up:
Many of our clients report great success using 9 Hz +/- and 16 Hz +/- as treatment frequencies with treatments starting with the 808nm 150mw wand for about one or two minutes per treatment area and then using the 635nm 5mw wand for about four minutes per treatment area. One theory is the deeper penetrating 808nm wand and the less penetrating 635nm wand treat surrounding tissue that may also be irritated or inflamed.
Suggested set up:
- 1. Turn on power switch on back of unit, slide the wand into the connector on top left corner of the power supply and twist 1/4 turn to the right to lock.
- 2. Push the FIRST button TWICE. The display above it to the left will read 2.
- 3. Push the SECOND (PULSE RANGE) button TWICE for (2 Hz +/- to 20 Hz +/-)
or THREE times for (20 Hz +/- to 200 Hz +/-)
- 4. Push the THIRD (RUN) button ONCE. The unit is now set to run in the selected range and wave 2 (a square wave output) to the wands.
- 5. Adjust the pulse rate of the laser light flashing with the PULSE RATE
(lower left knob). The pulse rate is displayed on the left display.
- * The VOLTAGE knob is the lower right knob. It controls voltage to the laser wand. Voltage is displayed on the right display. Set the wand operating voltage to 6.3 +/- volts for the 635 wand or 8.0 +/- volts for the 808 wand.
- * The DUTY CYCLE knob is usually set to 3/4 duty for a crisp pulse. This upper right knob determines how long the pulse width is to the wand. We recommend 75% power on (duty) setting.
- * The STAND-BY buttons are both left outward, if pushed inwards, voltage is lowered. For “STAND-BY” push in either or both buttons.
- The most common reason the wand will not light up is one or both of the
STAND-BY buttons have been pushed, reducing the voltage.
Marketed by: www.ColdLaserTherapy.us
Manufactured by: HealingLasers, Austin, Texas, US. (Patent Pending (USA))
FDA Facility Establishment Registration Number: 3004857915
Important information all buyers must accept prior to purchase!
In order to avoid possible eye damage the use of laser goggles is NECESSARY by everyone in the room where any laser equipment is in use.
Using cold lasers or low level lasers on others may be considered practicing medicine. It is solely the purchasers responsibility to conform to all applicable laws and regulations!
We supply and custom made cold laser components for scientific and medical research use (pain reduction and other conditions) to medical professionals and clinicians only.
Photos on this site depict user assembled equipment (assembly consists of one simple twist or push connection).
The contents of this web site, cold laser equipment, low level laser equipment, other equipment, components and or cold laser parts, low level laser parts, other parts, purchased from this web site and other material contained on the this web site are for informational and scientific research purposes only. We do not render medical advice or represent products we sell are FDA approved or will achieve specific results. The information provided through this web site should not be used in the diagnosis of disease or other conditions or in the cure, mitigation, treatment, or prevention of disease, or is intended to affect the structure or function of the body. If you have or suspect you may have a health problem, you should consult your licensed health care provider.
Equipment and components purchased from this web site are manufactured by and for Healing Lasers Design Company, Cape Girardeau, MO and are sold by Accurate Inspections, Inc., a New Jersey Corporation doing business as Laser-Therapy.US.
Reverse engineering of our designs is strictly prohibited and aggressively prosecuted.
In order to avoid possible eye damage the use of laser goggles is NECESSARY by everyone in the room where any laser equipment is in use.
Using cold lasers or low level lasers on others may be considered practicing medicine. It is solely the purchasers responsibility to conform to all applicable laws and regulations!
We supply and custom made cold laser components for scientific and medical research use (pain reduction and other conditions) to medical professionals and clinicians only.
Photos on this site depict user assembled equipment (assembly consists of one simple twist or push connection).
The contents of this web site, cold laser equipment, low level laser equipment, other equipment, components and or cold laser parts, low level laser parts, other parts, purchased from this web site and other material contained on the this web site are for informational and scientific research purposes only. We do not render medical advice or represent products we sell are FDA approved or will achieve specific results. The information provided through this web site should not be used in the diagnosis of disease or other conditions or in the cure, mitigation, treatment, or prevention of disease, or is intended to affect the structure or function of the body. If you have or suspect you may have a health problem, you should consult your licensed health care provider.
Equipment and components purchased from this web site are manufactured by and for Healing Lasers Design Company, Cape Girardeau, MO and are sold by Accurate Inspections, Inc., a New Jersey Corporation doing business as Laser-Therapy.US.
Reverse engineering of our designs is strictly prohibited and aggressively prosecuted.
